Contents

• Notices
• 1 Active Mirror Control*
• 2 Robotic Pool Player
• 3 Soap-Film Tunnel
• 4 Eel-Like Bio-Mimetic Propulsion Device
• 5 Hot-Air Balloon Burner
• 6 Wind Tunnel Flight Simulator
• 7 Design of a laboratory-scale solar furnace for lime production
• 8 Assessment of building performance*
• 9 Experimental investigation of Radiant Porous Burner
• 10 Design of a New Innovative Coil
• 11 Comparison of indices of indoor air quality for underfloor- and overhead-air distribution systems using computational fluid dynamics
• 12 Design and Build of Spray Nozzle for use in Flameless Oxidation Burner
• 13 Aerodynamic Modification of Wingtips on the RAAF P3 Orion Aircraft
• 14 Surveillance Camera Platform for a Piper Seneca II Aircraft
• 15 Investigation of an Electrically Powered Aircraft
• 16 Investigating the effect of water and corrosive substances on fatigue life
• 17 Micro-mouse Development 1*
• 18 Mobile robot development
• 19 Underwater robot project
• 20 Multi-robot collaboration
• 21 Automatic Assembly of MDO Lourve Blades*
• 22 Investigation of hydrogen assisted cold cracking in steels
• 23 Stress analysis of aircraft wings repaired using friction welding
• 24 The influence of third phases on the performance of super duplex stainless steel welds
• 25 Formula SAE
• 26 Design, analysis and construction of a synthetic spinal segment
• 27 Design, analysis and construction of a synthetic skull / neck joint
• 28 Design, analysis and construction of a synthetic hip joint
• 29 Development of optimized structural member
• 30 Internal Mirror Memory*
• 31 Exhaust stack directivity
• 32 Design of a monster sound source
• 33 Plenum Chamber Attenuation
• 34 GPS Differential Carrier Phase Measurements for Attitude Determination
• 35 Mechanical Handling of Beer Kegs into a Cellar*
• 36 Vine Maintenance Work Platform*
• 37 Microwave Weed Controller*
• 38 World Solar Challenge Car Design
• 39 Skidding of motor vehicle on bitumen vs. dirt*
• 40 Validation of Physical and Mathematical Modelling Criteria for Advanced Gyro-Therm Burners*
• 41 Flow over towed underwater sonar arrays*
• 42 The Design and Construction of a Self Sustaining Radial Flow Gas Turbine
• 43 The Floating Exhaust Stack
• 44 Unloading of Beer Kegs from the Back of a Truck*
• 45 Auto-Positioning Vine Trimmer*
• 46 Embedded Active Control Systems in Passive Silencers*
• 47 Development of a dual-fuel Precessing Jet nozzle to reduce NOx emissions, and increase radiant heat transfer in rotary kilns
• 48 Examining the flow through large sudden planar expansions
• 49 Quantifying the soot volume fraction in flames from a range of advanced burner designs
• 50 Self-learning Robotic System
• 51 Vibration of towed underwater sonar arrays
• 52 Temperature control stress modelling of a weld thermal simulator
• 53 Thermal modelling of heat affected samples produced in a weld thermal simulator
• 54 Steels for laser cutting
• 55 Effect of weld profile on the fatigue/torsion performance of components
• 56 Environmental influence on the performance of components subjected to low cycle fatigue
• 57 Design of a microphone array package
• 58 C170 Wing Clip*
• 59 C170 Heated Glass*
• 60 P131 Spring/Clip Removal*
• 61 Cost Saving Investigations*
• 62 Automatic Guided Vehicle's*
• 63 Mirror Actuator Noise Reduction*
• 64 Integrated Mirror-Aerial System*
• 65 Mirror Bracket*
• 66 P131 Glass Dampening System*
• 67 Study of a particular micro motion manipulator*
• 68 Investigation of RailBAM microphone array directivity*
• 69 Development of a low frequency windscreen for gust attenuation of blast noise measurement microphones*
• 70 Investigation of Aging Aircraft Engines and Resulting Maintenance Schedules
• 71 Preferences: by Student
• Projects listed by Supervisor
• About this document ...